Коды ошибок MegaRAID LSI / MegaRAID Event Messages

Всем привет, хочу поделиться с вами кодами ошибок MegaRAID LSI, хотя эта памятка больше для себя. Знание кодов ошибок сильно помогает с решением проблем и общению с технической поддержкой, где вы всегда можете понять степень риска ваших данных, можно ли еще подождать и не торопиться с заменой оборудования или же уже пора перевозить сервисы или виртуальные машины на запасные сервера.

Коды ошибок MegaRAID LSI / MegaRAID Event Messages

0x0000 Information MegaRAID firmware initialization started (PCI ID %04x/%04x/%04x/%04x)
0x0001 Information MegaRAID firmware version %s
0x0002 Fatal Unable to recover cache data from TBBU
0x0003 Information Cache data recovered from TBBU successfully
0x0004 Information Configuration cleared
0x0005 Warning Cluster down; communication with peer lost
0x0006 Information Virtual drive %s ownership changed from %02x to %02x
0x0007 Information Alarm disabled by user
0x0008 Information Alarm enabled by user
0x0009 Information Background initialization rate changed to %d%%
0x000a Fatal Controller cache discarded due to memory/battery problems
0x000b Fatal Unable to recover cache data due to configuration mismatch
0x000c Information Cache data recovered successfully
0x000d Fatal Controller cache discarded due to firmware version incompatibility
0x000e Information Consistency Check rate changed to %d%%
0x000f Fatal Fatal firmware error: %s
0x0010 Information Factory defaults restored
0x0011 Information Flash downloaded image corrupt
0x0012 Critical Flash erase error
0x0013 Critical Flash timeout during erase
0x0014 Critical Flash error
0x0015 Information Flashing image: %s
0x0016 Information Flash of new firmware image(s) complete
0x0017 Critical Flash programming error
0x0018 Critical Flash timeout during programming
0x0019 Critical Flash chip type unknown
0x001a Critical Flash command set unknown
0x001b Critical Flash verify failure
0x001c Information Flush rate changed to %d seconds
0x001d Information Hibernate command received from host
0x001e Information Event log cleared
0x001f Information Event log wrapped
0x0020 Fatal Multi-bit ECC error: ECAR=%x, ELOG=%x, (%s)
0x0021 Warning Single-bit ECC error: ECAR=%x, ELOG=%x, (%s)
0x0022 Fatal Not enough controller memory
0x0023 Information Patrol Read complete
0x0024 Information Patrol Read paused
0x0025 Information Patrol Read Rate changed to %d%%
0x0026 Information Patrol Read resumed
0x0027 Information Patrol Read started
0x0028 Information Rebuild rate changed to %d%%
0x0029 Information Drive group modification rate changed to %d%%
0x002a Information Shutdown command received from host
0x002b Information Test event: %s
0x002c Information Time established as %s; (%d seconds since power on)
0x002d Information User entered firmware debugger
0x002e Warning Background Initialization aborted on %s
0x002f Warning Background Initialization corrected medium error (%s at %lx
0x0030 Information Background Initialization completed on %s
0x0031 Fatal Background Initialization completed with uncorrectable errors on %s
0x0032 Fatal Background Initialization detected uncorrectable double medium errors (%s at %lx on %s)
0x0033 Critical Background Initialization failed on %s
0x0034 Progress Background Initialization progress on %s is %s
0x0035 Information Background Initialization started on %s
0x0036 Information Policy change on %s from %s to %s
0x0038 Warning Consistency Check aborted on %s
0x0039 Warning Consistency Check corrected medium error (%s at %lx
0x003a Information Consistency Check done on %s
0x003b Information Consistency Check done with corrections on %s
0x003c Fatal Consistency Check detected uncorrectable double medium errors (%s at %lx on %s)
0x003d Critical Consistency Check failed on %s
0x003e Fatal Consistency Check completed with uncorrectable data on %s
0x003f Warning Consistency Check found inconsistent parity on %s at strip %lx
0x0040 Warning Consistency Check inconsistency logging disabled on %s (too many inconsistencies)
0x0041 Progress Consistency Check progress on %s is %s
0x0042 Information Consistency Check started on %s
0x0043 Warning Initialization aborted on %s
0x0044 Critical Initialization failed on %s
0x0045 Progress Initialization progress on %s is %s
0x0046 Information Fast initialization started on %s
0x0047 Information Full initialization started on %s
0x0048 Information Initialization complete on %s
0x0049 Information LD Properties updated to %s (from %s)
0x004a Information Drive group modification complete on %s
0x004b Fatal Drive group modification of %s stopped due to unrecoverable errors
0x004c Fatal Reconstruct detected uncorrectable double medium errors (%s at %lx on %s at %lx)
0x004d Progress Drive group modification progress on %s is %s
0x004e Information Drive group modification resumed on %s
0x004f Fatal Drive group modification resume of %s failed due to configuration mismatch
0x0050 Information Modifying drive group started on %s
0x0051 Information State change on %s from %s to %s
0x0052 Information Drive Clear aborted on %s
0x0053 Critical Drive Clear failed on %s (Error %02x)
0x0054 Progress Drive Clear progress on %s is %s
0x0055 Information Drive Clear started on %s
0x0056 Information Drive Clear completed on %s
0x0057 Warning Error on %s (Error %02x)
0x0058 Information Format complete on %s
0x0059 Information Format started on %s
0x005a Critical Hot Spare SMART polling failed on %s (Error %02x)
0x005b Information Drive inserted: %s
0x005c Warning Drive %s is not supported
0x005d Warning Patrol Read corrected medium error on %s at %lx
0x005e Progress Patrol Read progress on %s is %s
0x005f Fatal Patrol Read found an uncorrectable medium error on %s at %lx
0x0060 Critical Predictive failure: CDB: %s
0x0061 Fatal Patrol Read puncturing bad block on %s at %lx
0x0062 Information Rebuild aborted by user on %s
0x0063 Information Rebuild complete on %s
0x0064 Information Rebuild complete on %s
0x0065 Critical Rebuild failed on %s due to source drive error
0x0066 Critical Rebuild failed on %s due to target drive error
0x0067 Progress Rebuild progress on %s is %s
0x0068 Information Rebuild resumed on %s
0x0069 Information Rebuild started on %s
0x006a Information Rebuild automatically started on %s
0x006b Critical Rebuild stopped on %s due to loss of cluster ownership
0x006c Fatal Reassign write operation failed on %s at %lx
0x006d Fatal Unrecoverable medium error during rebuild on %s at %lx
0x006e Information Corrected medium error during recovery on %s at %lx
0x006f Fatal Unrecoverable medium error during recovery on %s at %lx
0x0070 Information Drive removed: %s
0x0071 Warning Unexpected sense: %s, CDB%s, Sense: %s
0x0072 Information State change on %s from %s to %s
0x0073 Information State change by user on %s from %s to %s
0x0074 Warning Redundant path to %s broken
0x0075 Information Redundant path to %s restored
0x0076 Information Dedicated Hot Spare Drive %s no longer useful due to deleted drive group
0x0077 Critical SAS topology error: Loop detected
0x0078 Critical SAS topology error: Unaddressable device
0x0079 Critical SAS topology error: Multiple ports to the same SAS address
0x007a Critical SAS topology error: Expander error
0x007b Critical SAS topology error: SMP timeout
0x007c Critical SAS topology error: Out of route entries
0x007d Critical SAS topology error: Index not found
0x007e Critical SAS topology error: SMP function failed
0x007f Critical SAS topology error: SMP CRC error
0x0080 Critical SAS topology error: Multiple subtractive
0x0081 Critical SAS topology error: Table to table
0x0082 Critical SAS topology error: Multiple paths
0x0083 Fatal Unable to access device %s
0x0084 Information Dedicated Hot Spare created on %s (%s)
0x0085 Information Dedicated Hot Spare %s disabled
0x0086 Critical Dedicated Hot Spare %s no longer useful for all drive groups
0x0087 Information Global Hot Spare created on %s (%s)
0x0088 Information Global Hot Spare %s disabled
0x0089 Critical Global Hot Spare does not cover all drive groups
0x008a Information Created %s}
0x008b Information Deleted %s}
0x008c Information Marking LD %s inconsistent due to active writes at shutdown
0x008d Information Battery Present
0x008e Warning Battery Not Present
0x008f Information New Battery Detected
0x0090 Information Battery has been replaced
0x0091 Critical Battery temperature is high
0x0092 Warning Battery voltage low
0x0093 Information Battery started charging
0x0094 Information Battery is discharging
0x0095 Information Battery temperature is normal
0x0096 Fatal Battery needs to be replacement, SOH Bad
0x0097 Information Battery relearn started
0x0098 Information Battery relearn in progress
0x0099 Information Battery relearn completed
0x009a Critical Battery relearn timed out
0x009b Information Battery relearn pending: Battery is under charge
0x009c Information Battery relearn postponed
0x009d Information Battery relearn will start in 4 days
0x009e Information Battery relearn will start in 2 day
0x009f Information Battery relearn will start in 1 day
0x00a0 Information Battery relearn will start in 5 hours
0x00a1 Information Battery removed
0x00a2 Information Current capacity of the battery is below threshold
0x00a3 Information Current capacity of the battery is above threshold
0x00a4 Information Enclosure (SES) discovered on %s
0x00a5 Information Enclosure (SAFTE) discovered on %s
0x00a6 Critical Enclosure %s communication lost
0x00a7 Information Enclosure %s communication restored
0x00a8 Critical Enclosure %s fan %d failed
0x00a9 Information Enclosure %s fan %d inserted
0x00aa Critical Enclosure %s fan %d removed
0x00ab Critical Enclosure %s power supply %d failed
0x00ac Information Enclosure %s power supply %d inserted
0x00ad Critical Enclosure %s power supply %d removed
0x00ae Critical Enclosure %s SIM %d failed
0x00af Information Enclosure %s SIM %d inserted
0x00b0 Critical Enclosure %s SIM %d removed
0x00b1 Warning Enclosure %s temperature sensor %d below warning threshold
0x00b2 Critical Enclosure %s temperature sensor %d below error threshold
0x00b3 Warning Enclosure %s temperature sensor %d above warning threshold
0x00b4 Critical Enclosure %s temperature sensor %d above error threshold
0x00b5 Critical Enclosure %s shutdown
0x00b6 Warning Enclosure %s not supported; too many enclosures connected to port
0x00b7 Critical Enclosure %s firmware mismatch
0x00b8 Warning Enclosure %s sensor %d bad
0x00b9 Critical Enclosure %s phy %d bad
0x00ba Critical Enclosure %s is unstable
0x00bb Critical Enclosure %s hardware error
0x00bc Critical Enclosure %s not responding
0x00bd Information SAS/SATA mixing not supported in enclosure; Drive %s disabled
0x00be Information Enclosure (SES) hotplug on %s was detected, but is not supported
0x00bf Information Clustering enabled
0x00c0 Information Clustering disabled
0x00c1 Information Drive too small to be used for auto-rebuild on %s
0x00c2 Information BBU enabled; changing WT virtual drives to WB
0x00c3 Warning BBU disabled; changing WB virtual drives to WT
0x00c4 Warning Bad block table on drive %s is 80% full
0x00c5 Fatal Bad block table on drive %s is full; unable to log block %lx
0x00c6 Information Consistency Check Aborted due to ownership loss on %s
0x00c7 Information Background Initialization (BGI) Aborted Due to Ownership Loss on %s
0x00c8 Critical Battery/charger problems detected; SOH Bad
0x00c9 Warning Single-bit ECC error: ECAR=%x, ELOG=%x, (%s); warning threshold exceeded
0x00ca Critical Single-bit ECC error: ECAR=%x, ELOG=%x, (%s); critical threshold exceeded
0x00cb Critical Single-bit ECC error: ECAR=%x, ELOG=%x, (%s); further reporting disabled
0x00cc Critical Enclosure %s Power supply %d switched off
0x00cd Information Enclosure %s Power supply %d switched on
0x00ce Critical Enclosure %s Power supply %d cable removed
0x00cf Information Enclosure %s Power supply %d cable inserted
0x00d0 Information Enclosure %s Fan %d returned to normal
0x00d1 Information BBU Retention test was initiated on previous boot
0x00d2 Information BBU Retention test passed
0x00d3 Critical BBU Retention test failed!
0x00d4 Information NVRAM Retention test was initiated on previous boot
0x00d5 Information NVRAM Retention test passed
0x00d6 Critical NVRAM Retention test failed!
0x00d7 Information %s test completed %d passes successfully
0x00d8 Critical %s test FAILED on %d pass. Fail data: errorOffset=%x goodData=%x badData=%x
0x00d9 Information Self check diagnostics completed
0x00da Information Foreign Configuration detected
0x00db Information Foreign Configuration imported
0x00dc Information Foreign Configuration cleared
0x00dd Warning NVRAM is corrupt; reinitializing
0x00de Warning NVRAM mismatch occurred
0x00df Warning SAS wide port %d lost link on PHY %d
0x00e0 Information SAS wide port %d restored link on PHY %d
0x00e1 Warning SAS port %d, PHY %d has exceeded the allowed error rate
0x00e2 Warning Bad block reassigned on %s at %lx to %lx
0x00e3 Information Controller Hot Plug detected
0x00e4 Warning Enclosure %s temperature sensor %d differential detected
0x00e5 Information Drive test cannot start. No qualifying drives found
0x00e6 Information Time duration provided by host is not sufficient for self check
0x00e7 Information Marked Missing for %s on drive group %d row %d
0x00e8 Information Replaced Missing as %s on drive group %d row %d
0x00e9 Information Enclosure %s Temperature %d returned to normal
0x00ea Information Enclosure %s Firmware download in progress
0x00eb Warning Enclosure %s Firmware download failed
0x00ec Warning %s is not a certified drive
0x00ed Information Dirty cache data discarded by user
0x00ee Information Drives missing from configuration at boot
0x00ef Information Virtual drives (VDs) missing drives and will go offline at boot: %s
0x00f0 Information VDs missing at boot: %s
0x00f1 Information Previous configuration completely missing at boot
0x00f2 Information Battery charge complete
0x00f3 Information Enclosure %s fan %d speed changed
0x00f4 Information Dedicated spare %s imported as global due to missing arrays
0x00f5 Information %s rebuild not possible as SAS/SATA is not supported in an array
0x00f6 Information SEP %s has been rebooted as a part of enclosure firmware download. SEP will be unavailable until this process completes.
0x00f7 Information Inserted PD: %s Info: %s
0x00f8 Information Removed PD: %s Info: %s
0x00f9 Information VD %s is now OPTIMAL
0x00fa Warning VD %s is now PARTIALLY DEGRADED
0x00fb Critical VD %s is now DEGRADED
0x00fc Fatal VD %s is now OFFLINE
0x00fd Warning Battery requires reconditioning; please initiate a LEARN cycle
0x00fe Warning VD %s disabled because RAID-5 is not supported by this RAID key
0x00ff Warning VD %s disabled because RAID-6 is not supported by this controller
0x0100 Warning VD %s disabled because SAS drives are not supported by this RAID key
0x0101 Warning PD missing: %s
0x0102 Warning Puncturing of LBAs enabled
0x0103 Warning Puncturing of LBAs disabled
0x0104 Critical Enclosure %s EMM %d not installed
0x0105 Information Package version %s
0x0106 Warning Global affinity Hot Spare %s commissioned in a different enclosure
0x0107 Warning Foreign configuration table overflow
0x0108 Warning Partial foreign configuration imported, PDs not imported:%s
0x0109 Information Connector %s is active
0x010a Information Board Revision %s
0x010b Warning Command timeout on PD %s, CDB:%s
0x010c Warning PD %s reset (Type %02x)
0x010d Warning VD bad block table on %s is 80% full
0x010e Fatal VD bad block table on %s is full; unable to log block %lx (on %s at %lx)
0x010f Fatal Uncorrectable medium error logged for %s at %lx (on %s at %lx)
0x0110 Information VD medium error corrected on %s at %lx
0x0111 Warning Bad block table on PD %s is 100% full
0x0112 Warning VD bad block table on PD %s is 100% full
0x0113 Fatal Controller needs replacement, IOP is faulty
0x0114 Information CopyBack started on PD %s from PD %s
0x0115 Information CopyBack aborted on PD %s and src is PD %s
0x0116 Information CopyBack complete on PD %s from PD %s
0x0117 Progress CopyBack progress on PD %s is %s
0x0118 Information CopyBack resumed on PD %s from %s
0x0119 Information CopyBack automatically started on PD %s from %s
0x011a Critical CopyBack failed on PD %s due to source %s error
0x011b Warning Early Power off warning was unsuccessful
0x011c Information BBU FRU is %s
0x011d Information %s FRU is %s
0x011e Information Controller hardware revision ID %s
0x011f Warning Foreign import shall result in a backward incompatible upgrade of configuration metadata
0x0120 Information Redundant path restored for PD %s
0x0121 Warning Redundant path broken for PD %s
0x0122 Information Redundant enclosure EMM %s inserted for EMM %s Number Type Event Text
0x0123 Information Redundant enclosure EMM %s removed for EMM %s
0x0124 Warning Patrol Read can't be started, as PDs are either not ONLINE, or are in a VD with an active process, or are in an excluded VD
0x0125 Information Copyback aborted by user on PD %s and src is PD %s
0x0126 Critical Copyback aborted on hot spare %s from %s, as hot spare needed for rebuild
0x0127 Warning Copyback aborted on PD %s from PD %s, as rebuild required in the array
0x0128 Fatal Controller cache discarded for missing or offline VD %s. When a VD with cached data goes offline or missing during runtime,
the cache for the VD is discarded. Because the VD isoffline, the cache cannot be saved.
0x0129 Information Copyback cannot be started as PD %s is too small for src PD %s
0x012a Information Copyback cannot be started on PD %s from PD %s, as SAS/SATA is not supported in an array
0x012b Information Microcode update started on PD %s
0x012c Information Microcode update completed on PD %s
0x012d Warning Microcode update timeout on PD %s
0x012e Warning Microcode update failed on PD %s
0x012f Information Controller properties changed
0x0130 Information Patrol Read properties changed
0x0131 Information CC Schedule properties changed
0x0132 Information Battery properties changed
0x0133 Warning Periodic Battery Relearn is pending. Please initiate manual learn cycle as Automatic learn is not enabled
0x0134 Information Drive security key created
0x0135 Information Drive security key backed up
0x0136 Information Drive security key from escrow, verified
0x0137 Information Drive security key changed
0x0138 Warning Drive security key, re-key operation failed
0x0139 Warning Drive security key is invalid
0x013a Information Drive security key destroyed
0x013b Warning Drive security key from escrow is invalid
0x013c Information VD %s is now secured
0x013d Warning VD %s is partially secured
0x013e Information PD %s security activated
0x013f Information PD %s security disabled
0x0140 Information PD %s is reprovisioned
0x0141 Information PD %s security key changed
0x0142 Fatal Security subsystem problems detected for PD %s
0x0143 Fatal Controller cache pinned for missing or offline VD %s
0x0144 Fatal Controller cache pinned for missing or offline VDs: %s
0x0145 Information Controller cache discarded by user for VDs: %s
0x0146 Information Controller cache destaged for VD %s
0x0147 Warning Consistency Check started on an inconsistent VD %s
0x0148 Warning Drive security key failure, cannot access secured configuration
0x0149 Warning Drive security password from user is invalid
0x014a Warning Detected error with the remote battery connector cable
0x014b Information Power state change on PD %s from %s to %s
0x014c Information Enclosure %s element (SES code 0x%x) status changed
0x014d Information PD %s rebuild not possible as HDD/SSD mix is not supported in a drive group
0x014e Information Copyback cannot be started on PD %s from %s, as HDD/SSD mix is not supported in a drive group
0x014f Information VD bad block table on %s is cleared
0x0150 Caution SAS topology error: 0x%lx[/wpspoiler]

Вот такой полезный список ошибок MegaRAID LSI / MegaRAID Event Messages

Материал сайта pyatilistnik.org